Qnap qfinder cannot find nas7/12/2023 ![]() If your RAID seems Unmounted, Not Active or Synchronizing stucks at %0 after first time Installation Please fallow this document ( Sometime New HDDs comes with “Bad sector” problem, and we’ll Identify which HDD is Infected.) If problem still exist, start installation from begining ![]() +If Installation completes, but coulnt enter login, just clean explorer cookies, or try another web borowser (Firefox, Chrome). Start Qnap Installion with 1 or 2 Tb HDDs, upgrade device firmware and than start Installaion with this 3 or 4 TB HDD’s again.Ĭ – Screen comes Corrupted at first time installation If you try to start Installation lower Firmware with these 3 / 4 TB HDD’s, their size seems as “0 mb” or installation may failed. +If you’r using 3 or 4 TB’ HDD’s just be sure that your Qnap firmware version is 3.5.0 or higher. If it still doestn recognize HDD, just dont use it. +If Qnap doesnt recognize one of your HDD, just change HDD slot with another one. Dont forget, Ts 459U and Ts-459 PII doesnt use same firmware. +If Qnap get this error, just be sure that you download right firmware. +Press around 15 second to Qnap’s reset Button. +Be sure if Qnap and your laptop / Pc is is in same Ip subnet Range.(If Qnap Ip is 192.168.2.91, Your computer IP adres must be 192.168.2.x) Directly Plug Qnap Ethernet cable to this Pc. +Use another laptop / Pc whis is not joined your network, close Antivirus & Firwall. +Just be sure that Ip adress that you give to Qnap is not exist at another Network device on your Network. Go to Administration Panel, and insert another HDD to one of Qnap HDD slots.ĥ – Start formatting that HDD, (Choose Single disk in RAID menu)Ħ – After this process complete, format other HDD’s with the same way.ħ – If one of that HDD’s coulnd be format, or give “Read / Write” / “Abnormal” or “Normal” Error, dont use that HDD, and Plug out.Ĩ – If all HDDs, seems fine, choose your RAID, choose all HDD’s and start RAID Rebuilding.Ī – Could not Enter Qnap Installation Screen Select your device model (Check Storage of Archive) and your device model.Ģ – Open Qnapfinder, and start installationģ – On Installation steps, Qnap ask you to insert an HDD, and Plug only 2.th HDD (Dont use 1.st HDD, or dont Plug in all HDDs), and finish installation with “Single Disk”Ĥ – After 15th minutes later, Qnap should format HDD and could be accessable. Dont forget that you can change all of these settings after installation Except RAID building.ġ4 – RAID Installation may take around 4-12 Hours, so dont try to close device while this process is running, My advie is also choose “Thin Volume” to make enable “Snatshot” featureġ3 – On final step, Qnap ask you to confirm this settings. If you have more than 5 HDD, choose RAID 6 If you want to format HDDS and need fresh install, just click on “Initilize System”Ĩ – Your time server settings (My advice is choosing this manually)ĩ – Choose your Qnap IP adress dont forget that, this IP adress means your Qnap first ethernet port,ġ0 – Setup your Thunderbolt IP adress if you have one ġ1 – Dont forget to open Linux / Windows / Mac connection services ġ2 – On this RAID configration, my advice is ![]() If you use your HDD on another NAS before and dont want to loose data, just click Restore to Factory Settings”. XII – I Cannot Remember Which RAID I Install, How Can I Learn RAID Level Or My HDD’s?ġ – Power On Nas Witout HDDs, and Dont Plug till Qnap Wants you to plug a HDD,Ģ – Install Qnapfinder from 3 – A few minutes later, Qnapfinder should find your NAS.Ĥ – You can continiue installation bu double click on your nas, but My advice is, just type this IP number to your favorite Web browser XI – QNAP NAS Offical Frequently Asked Questions – First-time Installation & Setup X – Thing You Should Know After Installation / My Advices VIII – Qnap couldnt recognize one of my HDD VI – Questions & Answers about expanding capacity V – Must I use RAID? / How to setup multi-RAID? / Does Qnap Performance change if I build different RAID systems? III – How to configure Ip with same subnet II – Problem on First Time Installation?
0 Comments
Leave a Reply. |